• Help Support Hardline Crawlers :

Revive Retro

Took it for its first drive... It did ok. Tires are unbalanced and the carb seems a bit lean.

Bill came to take the rig for new wheels and he made it a block and came back---thing was now barely running..
 

Attachments

  • 20160602_192729.jpg
    20160602_192729.jpg
    60.6 KB · Views: 236
  • 20160602_192857.jpg
    20160602_192857.jpg
    53.9 KB · Views: 229
  • 20160602_193958.jpg
    20160602_193958.jpg
    33.8 KB · Views: 225
First found the converter was coming apart and plugged the exhaust. So that fell off.... :awesomework:
 

Attachments

  • 20160617_204721.jpg
    20160617_204721.jpg
    39 KB · Views: 226
So the fuel gauge also didn't work and bill wanted that fixed so I had him order a new sender. Well thats when I found the nasty nasty in the tank--lots of rust.

So I went ahead and had him order a new tank also.
 

Attachments

  • 20160616_203837.jpg
    20160616_203837.jpg
    46.6 KB · Views: 225
  • 20160616_212449.jpg
    20160616_212449.jpg
    46.4 KB · Views: 227
  • 20160620_181544.jpg
    20160620_181544.jpg
    78.4 KB · Views: 229
  • 20160620_204627.jpg
    20160620_204627.jpg
    49.5 KB · Views: 229
Also the same time the cat went the carb also started to flood over so I was going to rebuild that also. Good thing because there was a load of crap inside it.
 

Attachments

  • 20160619_192927.jpg
    20160619_192927.jpg
    52.6 KB · Views: 227
  • 20160617_210856.jpg
    20160617_210856.jpg
    52.4 KB · Views: 230
So a cross between some cat crap in the muffler and excessive fuel there was a load backfire and the muffler got opened up like a can and the cat chunks fell out. But the rig now has lots of balls and sounds like a race jeep :redneck:
 

Attachments

  • 20160620_210951.jpg
    20160620_210951.jpg
    34.9 KB · Views: 228
So one last thing to do was bleed the brakes. I never bled the fronts since they were never touched. Well this is where things went south.. All of a sudden a ton of air and no pedal--fawk..

So ya the master **** out and had to replace it. Now the brakes work sweet...
 

Attachments

  • 20160621_203102.jpg
    20160621_203102.jpg
    47.2 KB · Views: 218
  • 20160622_211421.jpg
    20160622_211421.jpg
    32.1 KB · Views: 226
So since Bill had left the wheels here I went ahead and dropped them off at my old work and had them mounted. They are like 3/4" offset when is what the rig needed. Now the tires don't rub the leafs on full lock and it really looks good now.

So thats it folks--this one is done.....:cheer:
 

Attachments

  • 20160623_195452.jpg
    20160623_195452.jpg
    79.1 KB · Views: 222
  • 20160623_195504.jpg
    20160623_195504.jpg
    82.1 KB · Views: 217
  • 20160623_195516.jpg
    20160623_195516.jpg
    69 KB · Views: 223
Jeep turned out great. Also a good reminder of the little things that go wrong when you let a rig sit for too long.

What straps is he using for holding the jerry cans to the holders? I am trying to source some for my rig.
 
Thanks Harv....

There actually are no straps. Its a an assembly thats part of the tire carrier that holds them down--kinda slick..
 
Bill came and grabbed the jeep on saturday and drove it to the garage where its going to be stored. Made it 5ft from the garage door when the carb had an issue with the float level. Said it drove great otherwise.

:bbbball:
 
Back
Top