• Help Support Hardline Crawlers :

Search results

  1. Skid Mark

    Toyota Solid Axle Vented Brake Upgrade

    Ive seen a home made conversion useing a chevy half ton IFS rotor and single piston caliper on both front and rear toyota axels. They just made brackets out of a couple pices of steel plate welded together and drilled to bolt on. I'm not sure what the years of the chevy truck parts came off of...
  2. Skid Mark

    SAS.....clunk...bang....

    After seeing its all new running gear up front I'd be leaning towards something not part of the suspension. I'd check both motor mounts first then I'd check body mounts
  3. Skid Mark

    SAS.....clunk...bang....

    upper and lower nuckel bearings:beer:
  4. Skid Mark

    Big Ass chainsaw!

    I have a older saw moter Still "somethen"56AV. My grandpas brother in law was a logger up in alaska and used it with a 4' bar as a saw mill. its had all the internal stuff done has no bar, chain and needs a sparkplug wire and still kicks and runs like a beast. I have to get it out of storage but...
  5. Skid Mark

    I drove off the trail, drunk, at night.

    Most times I've driven off the trail, Was because I never started on a trail in the first place. I've voluntarily made a bypass because My rig doesn't come equipped with flotation devices. I've made a new trail due to not having any open unregulated wheeling areas. Most times I've seen someone...
  6. Skid Mark

    4.0 jeep motors

    HELLLL YEA THANKS FELLAS I got off eairly so im pullen blocks and drinking high life Its miller time:beer::beer::beer::beer::beer::beer:
  7. Skid Mark

    4.0 jeep motors

    both out of an xj I need to take the block out of the 88 and put my head on it in my 95 long story but I had a bad starter now it a bad block and missing half a rod.. Good times :beer: thanks
  8. Skid Mark

    4.0 jeep motors

    Does anyone know if the block on a 88 1st gen will interchange with a 2nd gen from 94 thanks:beer:
  9. Skid Mark

    Internet Crankshaft ID test.

    the only thing I can think of is if they shaved off some weight in the inside on the crank to install larger rods or clearnced the crank instead of the block when putting the 400 crank in the 350 block.
  10. Skid Mark

    Help! 1992 5.8 runs rough

    Since everything else has been checked or replaced Id say check replace the Idle speed solenoid
  11. Skid Mark

    Muncie 4spd with transfercase??

    Yes on the 3 speed with a 4 speed overdrive gear and its an iron case not aluminum with driverside external linkedge. It did have an aluminum bellhousing and transfercase and Im just about positive its a np208 transfer :eeek: Yes this is what it looks like and I was told by the previous...
  12. Skid Mark

    Muncie 4spd with transfercase??

    Thats good to hear they can handle power. I'm a little worried about the close gear ratio being I plan on using this as the tow-rig. I'm going to pull everything out and giving it a once over before reassembly with the new motor. Thanks for the heads up on checking the output shaft. Question...
  13. Skid Mark

    Muncie 4spd with transfercase??

    So I picked up a 82 chevy truck for free with a bad engine and in need of a new rear end. It had been modified and had a muncie 4spd with overdrive and what looks like a np208 behind it. Ive never seen this before and did a little rersearch and found it is a popular sanddrag draceing combo. I...
  14. Skid Mark

    Flipping a NP205

    I have a np203 to th350/400 plate if u need one $20
  15. Skid Mark

    Balanced extended front drive line

    Thank you :beer: I'm located in Kitsap county But I'm willing to travel. The local shops dont do extended slip yokes. Do you have a number to reach Dave at? :beer:
  16. Skid Mark

    Balanced extended front drive line

    Does anyone know where a good deal is on having a stock front drive line extended slip yoke made and have it balenced Its on a 95 chevy I installed a SAS D44. I have both the stock ifs drive line and the 79 F250 stock DL that goes to the Highpinion D44. I wanted to see about useing the ends...
  17. Skid Mark

    Wheel studs/steering components

    Striped two chevy full size steering box arms snaped a doxen or so pitman arms on my old 94 toy. Killed toyota sas stock upper nuckel arm And I have snaped wheel studes just not wheeling And riped the steering box of the frame on a 79 GMC jimmy :redneck:
  18. Skid Mark

    T-Stat the great debate!!!

    And to think I was going to agree with ya fj but that guy said it so even you could understand. Believe it or not they think about the physics of water flow when they build engines.:flipoff: After I pinch them I drill a 1/8th inch hole in the thermostat right where that little flapper bypass...
  19. Skid Mark

    4.0 valves

    Mine ticked from a stuck lifter I put some Lucas oil stabilizer in it reved the **** out it and no more ticking On a side note it was sitting on its side for around 48 hours after I rolled it and it sat for another 2 months in my yard but I went out and charged the battery and it fired off with...
  20. Skid Mark

    Locker Question/Opinion

    weld patch?

Latest posts

Back
Top