• Help Support Hardline Crawlers :

Search results

  1. Jeepasaurusrex

    Q-Jet M4V

    I have a Q-Jet M4V on my 304. The my issue is getting the choke to work. I have the line hooked from the carb to the vacuum pull off. Another vacuum line goes from the carb to the heat tubes. Am I missing a line here somewhere? There is no other vacuum ports.
  2. Jeepasaurusrex

    Front axle wrap

    I think you should just put a Super Dana 30 under it and call it a day.
  3. Jeepasaurusrex

    Front axle wrap

    I like Tater Tots! :swing:
  4. Jeepasaurusrex

    Front axle wrap

    yea, that 401 V6 is a tiny motor....
  5. Jeepasaurusrex

    Front axle wrap

    Torch it all off and start over
  6. Jeepasaurusrex

    Front axle wrap

    Link it...:fawkdancesmiley:
  7. Jeepasaurusrex

    SPR/DMR Build

    My next long range rifle will be chambered in .338 Edge...:masturbanana[1]:
  8. Jeepasaurusrex

    Light weight welding helmet

    I might wear mine this Halloween... :redneck:
  9. Jeepasaurusrex

    Light weight welding helmet

    I have one of those leather hoods I keep for doing portable stuff. It folds up nice and compact too.
  10. Jeepasaurusrex

    predrilled for lock wire fasteners?

    Check some of the Aviation supply shops.
  11. Jeepasaurusrex

    Light weight welding helmet

    Unless your doing TIG all day, I prefer an old school flip helmet. No batteries to go dead or getting flashed because you didn't turn it on. They are cheaper, and way lighter.
  12. Jeepasaurusrex

    ID this trans/tcase

    T-10 transmission with a Spicer 18 w/overdrive. As a transmission in a Jeep, they suck. 1st gear is way too high.
  13. Jeepasaurusrex

    Is this enough penetration?

    When were running full speed at work, each welder will burn a 900lb box of wire a month.....:eeek:
  14. Jeepasaurusrex

    Is this enough penetration?

    When we build excavator or front end loader buckets, we don't use that flux core garbage. We use 1/16" hardwire or E71-T1 dual shield. I use either .035 hardwire or .045 Dual shield in my welder here at home. Lincoln PowerMig 200.
  15. Jeepasaurusrex

    Is this enough penetration?

    It will weld .030 dual shield just fine. Just use some 75/25 gas and your golden.
  16. Jeepasaurusrex

    Is this enough penetration?

    Pick up some E71-T1 dual shield. Run it with gas and it will lay in there like butter on hot bread. It will also stick to metal that is not clean.
  17. Jeepasaurusrex

    Excursions - Powerstroke

    $.40 a gallon less, but it uses twice as much fuel...... :eeek: The transmission in my F-350 has 168,000 miles on it and its pulling strong. Its all about keeping it cool and changing the fluid often. The stock transmission cooler is less than adequate. I added an aftermarket cooler and it made...
  18. Jeepasaurusrex

    Dad's stang...

    Mike, you and your family are in our thoughts and prayers.
  19. Jeepasaurusrex

    So i bought a 51 Whilly

    Hows that skid plate? :redneck:
  20. Jeepasaurusrex

    ID this axle?

    I have heard about the smooth case 60s under vans with the larger tubes, this looks like one. :corn:

Latest posts

Back
Top