• Help Support Hardline Crawlers :

Search results

  1. P

    Electric weedwackers

    I have a 24v kobalt trimmer & blower. It uses the 4.0ah batteries and has a claimed 15min run time. I can't say I trim that much, but it works fine for me. Just trimming and edging around the house. The 40 or 80v would be more powerful. I went 24v cuz I have other told that use the same...
  2. P

    Anything to do in Lenoir North Carolina?

    As said isnt much going on around here. But you will be ~ an hr from Charlotte/Mooresville, less than an hr from Boone/Blowing Rock, ~1.5hrs from Asheville. Plenty of stuff within a short drive depending on what your wanting to get into.
  3. P

    RCV Big Bells in 05+ F250/350 outers

    Re: Re: RCV Big Bells in 05+ F250/350 outers Did he say if they fit through the knuckle, or did he have to put it on after the Shay's were in? Sent from my SM-G955U using Tapatalk
  4. P

    My head hurts math.

    Nick's math is correct to get the right ratio, but I believe your total gear ratio is wrong. It should be 2.86 x 5.38 for 15.39 vs 2.86 + 5.38. So that would make the tire size need to be 7.25". If your current math works for the ecm, then disregard. Sent from my SM-G955U using Tapatalk
  5. P

    Time for a Side by Side

    I don't know about the ride, but they are a monster next to a rzr. Sent from my SM-G955U using Tapatalk
  6. P

    Bathroom runner/screwing around

    Biggest thing is make sure it's lite... If you don't have reverse it better be easy to push around. I like that trike, but throw on an old school truck bench seat. Or a love seat. Or something that looks like a toilet, put your beers inside. I think it almost has to have some boggers on it...
  7. P

    2008 jku bolt pattern

    Re: Re: 2008 jku bolt pattern The bolt circle is 5". It is 5 evenly spaced holes centered on that circle, 72* apart. Not sure what the hole size you need is. Sent from my SM-G955U using Tapatalk
  8. P

    Searched to death, grooving stickies sx

    How warm were the tires when you started grooving? Normally it goes alot better when you get the tire nice and warm first. Sent from my SM-G955U using Tapatalk
  9. P

    Anyone ever put a semi trailer on the ground ?

    We've always just dug out the ground, so that the rear is at ground level... Mainly incase we wanted to move it again in the future. Sent from my SM-G955U using Tapatalk
  10. P

    Atlanta

    Big Dave's cheesesteaks looks really good, but haven't been. Anyone else been? Sent from my SM-G955U using Tapatalk
  11. P

    Da burp cure

    Wonder if the BAD beadlocks have the same issue? Sent from my SM-G955U using Tapatalk
  12. P

    Da burp cure

    Yeah, that was understood, but good to point out. I've dealt with the same thing, along with bent lips. Running 20s seemed to not have as much issue with that, but there were other tradeoffs. Sent from my SM-G955U using Tapatalk
  13. P

    Da burp cure

    Re: Re: Da burp cure I've wondered if you could run a bunch of wraps on both beads, and avoid running beadlocks? Sent from my SM-G955U using Tapatalk
  14. P

    Yukon Dana 60 boring tool

    Call east coast gear supply. I think they rent theirs. Sent from my SM-G955U using Tapatalk
  15. P

    Time for a Side by Side

    If you can wait until end of model year, I have seen brand new rzrs in that price range. I have been looking at similar myself, biggest complaint I've heard against the mid-engine machines is noise and heat in the cab. Unless you need a 4seater, you could look at something like a ranger vs...
  16. P

    Portals N ****

    I'll be interested to see it all unfold. I am in a similar position in my EB. Are you putting the radiators in series? Think the stock pump can handle pushing through both? Sent from my SM-G955U using Tapatalk
  17. P

    Fords new 7.3 v8 gas motor

    If they can get the empty fuel mileage up, it would drive folks to buying gas more, IMO. I think ppl buy diesel because they believe it will get better mileage with more power.
  18. P

    Sold/Expired WTB: Early Bronco 1966-1977

    Re: Re: WTB: Early Bronco 1966-1977 And the problem is, you have a steal a decent one to have a chance at making money on them. The parts can be pricy if you have to replace many. But they are fun to drive/wheel.
  19. P

    Sold/Expired Start of a U4 Chassis Sold

    Re: Start of a U4 Chassis It also allows you to have a cnc cut and cope all the tubes. Makes it easier to sell as a kit, or for a race team, speeds up the build process esp when using chromoly.
  20. P

    Random Tech Pics that dont need a thread

    Re: Re: Random Tech Pics that dont need a thread That might work. It would need to be ~1" hole through the hub and rotor. Not sure how much room there is around the backside of the hub. I have had a few friends bend & break spindles. Not sure the adapter eliminates this risk, but that was my...

Latest posts

Back
Top