• Help Support Hardline Crawlers :

jeep

  1. S

    For Sale Jeep yj

    1994 yj king pin Dana 60 full hydo Dana 70 rear 4link rear 3 link front 4.0 ax15 Dana 300 with 4 to 1. 5.13 gears on board air works great just don’t have time to use like I want $18,500. Located in Scott depot wv
  2. G

    1983 Jeep cj-7 crawler

    https://www.facebook.com/marketplace/item/860922212016955/?mibextid=gVQsCx 1983 Jeep SBC 350 on propane Sm465 205 twin stick transfer case 5.38 gears Dana 60 front with 35 spline outers Detroit locker 14bolt rear welded 4 linked with 7075 links 1-1/4 heim joints 115 wb Racerunner 2.5 16" air...
  3. M

    Jeep Comanche $4000

    350 engine truck avenger off road carb. 700r4 trans 203 tcase 14 bolt rear 44 front. Leaf spring front and rear. Has 9000lb winch. Jeep was Rewired before New Years and installed sidewinder shifter. 38” super swampers. Comes with another front end and 2 38” swampers. Jeep runs good and goes...
  4. Ahamilton24

    2004 Jeep Wrangler LJ $37000 (42, tons, ORI)

    This is a clean fresh build. Has 1 trail ride on it to Hawk Pride. Jeep came from VA Beach and was immaculate. Have original pictures of the jeep. Frame was clean and no rust on the body. Built this as a crawler and going a different route with some things in life. Interested in an ultra 4 car...
  5. Ahamilton24

    2015 JK, Tons, ORI, 43s

    2015 JK Sport Willys 58k miles 113 wheelbase First off this jeep does have a rebuilt title. I bought the jeep from insurance from being drove in a ditch totaling the dana 30 and front fender. I done this to save money for the build. This thing just needs some bias ply tires to be street driven...
  6. M

    WTB D44, AEV Pintler

    I have a 2005 LJ that I am wanting to add a D44 out of a rubicon to. Also in search of a 17" AEV Pintler(s) in 5x4.5. Thanks! (256)four3eight-nine8eleven
  7. S

    2013 JEEP JKU ON SUPERDUTY TONS

    For sale: 2013 JKU Oscar Mike edt. Has 95,xxx miles Stock Motor Trans and Transfer In great condition. Super Duty axle swap with lockers and Chromos front and rear. Complete custom 1 off Suspension from Sunfire Offroad last summer. 3 link front with aluminum links 2.25 and 1.25 heims...
  8. S

    T18/Dana 20 Combo, set up for AMC 304

    For sale: T18 transmission/Dana 20 combo set up for AMC 304 -T18 with granny-low 1st gear (6.32:1 ratio) -Bolted to AMC 304 bellhousing -All bolted to a Dana 20 transfer case No leaks or issues, tight and ready to run with your next or current build $1,000 Located in the SF North Bay area...
  9. Smalls

    '92 YJ linked on D60's

    '92 Yj with 4.0, manual trans, and 241OR t-case. 9,000lb winch. 40" TSL's on TMI beadlocks. 117" wheel base. Front HpD60, 5.38 gears welded, 4 linked 7/8 heims w/ 14" air shocks, full hydro steering. 1310 driveshaft. Rear D60, 5.38 gears w/ spool, 4 linked 7/8 heims w/ 16" air shocks, TK1...
  10. DobermanRacing

    I have no idea what I'm doing aka the worst Ultra4 4400 build thread on Earth.

    Now that your expectations have been set. Welcome to my build thread. I'm going to speed through the old stuff to get you caught up. It's 2018. I bought a 98 Jeep XJ after discovering Jeepspeed with the intentions of racing in Jeepspeed 2700 (35" tire class). At this point I barely owned any...
  11. Ahamilton24

    2016 JKUR on Dana 60s

    2016 Jeep Wrangler AEV 350 74k miles Drivetrain: Stock 3.6 motor with S&B intake 5.5 inch AEV lift 43/14.50/17 TSL SX KMC Machette beadlocks powder coated candy Apple Red Spicer Ultimate Dana 60 5.38 gears Eaton lockers Yukon Chromoly shafts 1450 u joints Warn lockout hubs Tom Woods 1350 F/R...
  12. ChaseMacon

    Stretched Jk on tons

    Stretched JK on tons ($57,000) obo Avalanche grey 58K miles Freshly rebuilt by Baker Offroad Overall wheelbase 109" Fusion 4x4 custom width 73.5" axles Elite KP 60 front Shaved big tube 14 bolt 40 splined 5.38 gears and arb lockers Front suspension 3 linked 12" king coilovers with...
  13. GlipGlop

    LJ on Tons

    The LJ has been a work in progress since before I ever even had a driver's license. The Jeep is somewhat pulled together currently so I felt that it was a good time to start up a build thread in hopes to share some ideas. I am by no means a professional when it comes to fabrication and so please...

Latest posts

Back
Top