Reject Fab Buggy
All DOM Chassis 1 ¾" .120 wall
Overall height-68", Belly-19.5", Wheelbase-119"
5.3 LS engine with LS1 intake, Holley oil pan, Texas Speed 228r cam, retainers, seats, dual valve springs, chromoloy pushrods, viton valve stem seals, new oil pump, new water pump, custom headers, etc.
LS1 fuel filter/regulator with Walbro electric fuel pump
Fitech Ultimate LS standalone wiring harness
Fresh th350 built by Justin Holt with only a handful of rides on it, 3000 stall torque converter, dirt track shifter, TCI manual forward valve body, Derale transmission cooler with fan
NP205 transfer case with JB Fab twin stick shifters, shift rails, adjustable detents, etc.
Wide Open Designs carrier bearing with 1350 driveshafts
Radflo 14" coilovers with Viper coil springs
FOA 4" bump stops
Chevrolet Dana 60 front with locker, 35 spline Synergy drive flanges
14 bolt rear with spool and stock axle shafts
Disk brakes on all corners with new calipers, rotors, and pads
4 link front and rear with 1.25" heims
Wilwood dual master cylinder with all AN brake line fittings
39.5" TSL's on 8 bolt H1 wheels. Also have a spare wheel
Aluminum radiator with electric fan
Full hydro steering with PSC orbital, PSC steering shaft, dual ended ram, dual pass 12" power steering cooler
All AN fittings for fuel lines and -16 coolant lines.
Corbeau seats with 5.2 PRP harnesses
Optima red top battery, autometer gauges, 22" light bar
Buggy is in good shape and ready to ride. Chassis has not been beat up, never been rolled. It has been well maintained and taken care of and has been a great trail riding rig for me. I'm about 5'10 and fit with plenty of room. Buggy is located in Toney, Al. I have a parts list of everything that has gone into this rig and can provide that if wanted. Looking to get $21k. Not looking for any trades at this time.
All DOM Chassis 1 ¾" .120 wall
Overall height-68", Belly-19.5", Wheelbase-119"
5.3 LS engine with LS1 intake, Holley oil pan, Texas Speed 228r cam, retainers, seats, dual valve springs, chromoloy pushrods, viton valve stem seals, new oil pump, new water pump, custom headers, etc.
LS1 fuel filter/regulator with Walbro electric fuel pump
Fitech Ultimate LS standalone wiring harness
Fresh th350 built by Justin Holt with only a handful of rides on it, 3000 stall torque converter, dirt track shifter, TCI manual forward valve body, Derale transmission cooler with fan
NP205 transfer case with JB Fab twin stick shifters, shift rails, adjustable detents, etc.
Wide Open Designs carrier bearing with 1350 driveshafts
Radflo 14" coilovers with Viper coil springs
FOA 4" bump stops
Chevrolet Dana 60 front with locker, 35 spline Synergy drive flanges
14 bolt rear with spool and stock axle shafts
Disk brakes on all corners with new calipers, rotors, and pads
4 link front and rear with 1.25" heims
Wilwood dual master cylinder with all AN brake line fittings
39.5" TSL's on 8 bolt H1 wheels. Also have a spare wheel
Aluminum radiator with electric fan
Full hydro steering with PSC orbital, PSC steering shaft, dual ended ram, dual pass 12" power steering cooler
All AN fittings for fuel lines and -16 coolant lines.
Corbeau seats with 5.2 PRP harnesses
Optima red top battery, autometer gauges, 22" light bar
Buggy is in good shape and ready to ride. Chassis has not been beat up, never been rolled. It has been well maintained and taken care of and has been a great trail riding rig for me. I'm about 5'10 and fit with plenty of room. Buggy is located in Toney, Al. I have a parts list of everything that has gone into this rig and can provide that if wanted. Looking to get $21k. Not looking for any trades at this time.
