Finally....Da new rig..

oddball94 · Dec 12, 2016

oh man but i think axles would help lol what are you gonna run?

KarlVP · Dec 12, 2016

Titty sprinkles. Glad to see this project gaining traction.

Zoediak · Dec 13, 2016

Great work so far Crash!! Looking forward to your progress!

on your donor truck, what xfer case is in that?? does it have the 4 buttons on the dash for the shift controls??

I ask, because I need one for my '01 blazer, that and the TCC module inside the kickpanel on the pass side...

just curious if it (xfer case etc) was up for sale so I could get mine back on the road...

need to do some much needed love to my truck, but need a rig to drive in the mean time...

crash2 · Dec 13, 2016

Zoediak said:
Great work so far Crash!! Looking forward to your progress!

on your donor truck, what xfer case is in that?? does it have the 4 buttons on the dash for the shift controls??

I ask, because I need one for my '01 blazer, that and the TCC module inside the kickpanel on the pass side...

just curious if it (xfer case etc) was up for sale so I could get mine back on the road...

need to do some much needed love to my truck, but need a rig to drive in the mean time...

It left on saturday

So I made out pretty good. for what I sold my old tbi, cost of the truck and selling off the truck I am ahead $100

crash2 · Dec 19, 2016

MY new headers showed up finally (back order). I decided to go ahead and replace them since the early headers don't work on the vortec motor without notching the flange on the top side.

crash2 · Dec 19, 2016

So next I decided to go ahead and get the housings prepped. My original plan was to strip both housings of the brackets since they were so hammered and I am really thinking of going double ended ram on the steering.

One thing I love about the Pro-rocks is the suspension bridge--noo welding needed to the cast. To remove the bridge I had to cut the 1/2" plate for the old steering ram.

crash2 · Dec 19, 2016

Looks brand new again....

crash2 · Dec 19, 2016

Got the front housing all stripped.

crash2 · Dec 19, 2016

Time for the rear....

crash2 · Dec 19, 2016

Like the front I cut the nec items to remove the bridge and again cleaned it and the whole rear housing of the brackets. I left the brake caliper brackets on for now and more than likely I will be redoing them to roll the caliper down.

crash2 · Dec 19, 2016

Got the diffs lifted up and onto the table. I had to make holding fixtures for the diffs so they would stay in place,lol..

getting close to GO TIME,

crash2 · Dec 28, 2016

I got this a couple months ago to replace my worn out pro-tool notcher. Figured it was time to make the mount for it.

crash2 · Dec 28, 2016

Time to get this show on the road.

Like I had stated the bottom or "sled" was going to be strongly based off the S&N Bravo 2 chassis. First I had ALWAYS admired its design and the second awsome part is the fact I have all the jigs to aid me in doing so..

So after looking over man pictures and going up and measuring on it was time to jump into it.

I simply started by getting the skid roughed into place and getting the side jigs in place. Over the course of from this picture to the down the road I think I moved them around like 14 times,lol...

crash2 · Dec 28, 2016

I will say I am not super fast at this and I have messed up a couple bends but I do like to be as precise as I can--probably overly picky but I do like to be spot on.

crash2 · Dec 28, 2016

The skid plate is slowly taking on some shape....

crash2 · Dec 29, 2016

So one thing I found was the lower tube was too short which actually turned out to be a good thing. So I remade the front half of it and I sleeved the whole lower tube. Since that section of tube takes a good brunt of the beating I figured it wouldn't hurt to beef it up a bit.

crash2 · Dec 29, 2016

Since the lower tube was done went to the upper part.

crash2 · Dec 29, 2016

And the sled is done. Its hard to tell but I really pushed the front tube out an did this for a reason that I will go back to once the rest of the chassis is done. Feels good after over a week of work to have something...