Finally....Da new rig..

crash2 · May 3, 2017

If there was going to be a clearance issue then it would be with the suspension cycled this way. And it all clears with enough room I could easily lower the shaft from the motor 1/2" with a tad bit of room to spare.

crash2 · May 3, 2017

So with the clearances checked I finished up the mount.

crash2 · May 3, 2017

Tossed the driveshaft in since its needed for the next step.

crash2 · May 3, 2017

Time for the exhaust...

crash2 · May 8, 2017

So I got the Y pipe made and it turned out WAY better than I would have thought it would.

crash2 · May 8, 2017

Its DAMN tight but fits nicely.

crash2 · May 8, 2017

Now its time to make this fawker fit,lol...

crash2 · May 8, 2017

So since the drivetrain is all poly mounted I didn't want rubber mounts on the exhaust that would let it flop around. So I have a ton of these poly inserts but they are an oddball size so I had to machine 2mm off them for the closest material I had.

crash2 · May 8, 2017

Somehow I got everything to fit. So I used 2" tubing (as you can see by the driveshaft clearance I had to run 2"). Now the beauty of doing 2" and its 16 gauge tubing it fits nicely in my die for my bender so I was able to give it some small bends. It worked perfect.

crash2 · May 8, 2017

So I will be bouncing around on the rig until another batch of parts show up.

But I got the rear tail plate cut and mounted and holes for the new lights. These are 3 way lights (park/brake/backup)

crash2 · May 11, 2017

I decided to change it up a bit since I am waiting for more parts to arrive so I decided to get the tranny and fuel lines ran. I have always been a huge fan of secured lines with zero rub points.

crash2 · May 11, 2017

Next I made the fuel filter mount that also incorporates a holding fixture for the lines. I chose to put it where it was serviceable without tearing the car apart to access it.

crash2 · May 15, 2017

Next I made the fuel pump mount. Its mounted with a nice thick rubber pad to help with noise. Got the lines done up to it and out.

crash2 · May 15, 2017

The next part was a little tricky and required building something rather interesting. Due to the clearance I had to make a cradle of sorts that mounts to the tranny to mount the lines to.

crash2 · May 15, 2017

It was also rather snug at the driveshaft but fits like a glove. So as you can see its pretty elaborate but the lines are super secure and fits nicely with the tunnel cover in place.

crash2 · May 15, 2017

My plan was to get the powersteering pump mount done but it seems the pulley I had was wrong so had to order that. So for a while I will be bouncing around a bit. So I figured it was time to get the 4 point harness mounts done. I had to clearance the rear lower floor pan for the inner lower mounts. Got all the tabs made and mounts done--its got belts so another thing off the list.

crash2 · May 22, 2017

Like I stated early on my main intention is trail use and its being built more towards that side of it. So one thing I need is a place to store/carry my tools and suck and the back is the goal. So I started by pulling the rear winch and rotating the release handle down and then bent up a bottom that totally follows the contour within 1/4 to 1/2" trying to gain every square inch I can.

The base is 1/8" and it was a workout to put those few bends in it.

crash2 · May 22, 2017

Time to play with cardboard again,lol. So I got a good idea of hose I wanted it by this point. The front is sloped pretty good to give room for air flow for the trans cooler.

crash2 · May 22, 2017

So cut each panel out and tacked into place and then burned it all in---my tig is getting better but still not to where I wanna be.

crash2 · May 22, 2017

So next I made mounts for it and got them burned in.

Finally....Da new rig..

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments

-Oh no I picked a side-

Attachments