Annual Hangover run---Tonga

Bodaciouscj7 · Dec 4, 2010

Trying to get the jeep done in time for this. Haven't had a chance to play in the snow with the 42's or the new engine. Could be really interesting.

crash2 · Dec 4, 2010

Toyotanut said:
Not sure who got the trophey last year but the year b4 Morgan (not sure if he is on the board) got it.

Think I might have to do alittle maintence to my rig and go.

I think morgan has it--not sure. I might swing by and find out.

if not then its time to start a new NWW version :awesomework:

Wait---you getting permision to go play :fawkdancesmiley:

Bunk1 · Dec 4, 2010

HHmmmmmm

Toyotanut · Dec 4, 2010

crash said:
I think morgan has it--not sure. I might swing by and find out.

if not then its time to start a new NWW version :awesomework:

Wait---you getting permision to go play :fawkdancesmiley:

Think we should just start a NWW version. Yep got permission just like you:fawkdancesmiley:

Toyotanut · Dec 4, 2010

War-Jeeper said:
I dont have 220 at my parents place so i have to haul it to a friends here in snohomish to do it

How do you not have 220 at your parents? All homes should have it.... Don't know of one without. You just need an extention cord made to use it.

t1h5ta3 · Dec 4, 2010

hmmm... i might get out there for once... hang out neer the back of the pack if i have to.

Tayota · Dec 4, 2010

I'm running an 85 4runner with new 32x11.50 bfg km2's, locker in the rear - open front. Would I have any problems on this snow run? Where does everybody meet up at and what time?

War-Jeeper · Dec 5, 2010

Toyotanut said:
How do you not have 220 at your parents? All homes should have it.... Don't know of one without. You just need an extention cord made to use it.

Different plug and my mom would kill me:redneck: would have to run through the whole house and move the dryer to do it. No room on the panel to wire in a new plug either

Welded it up today, but found that my pinion bearing is toast (rather beyond it actually) So im out for this gotta pay for christmas gifts first so no money to fix the rig for a little while:booo:

99redtj · Dec 5, 2010

War-Jeeper said:
Different plug and my mom would kill me:redneck: would have to run through the whole house and move the dryer to do it. No room on the panel to wire in a new plug either

Welded it up today, but found that my pinion bearing is toast (rather beyond it actually) So im out for this gotta pay for christmas gifts first so no money to fix the rig for a little while:booo:

sam if really want a new 220 plug at your parents house i can heip you make room.

War-Jeeper · Dec 5, 2010

99redtj said:
sam if really want a new 220 plug at your parents house i can heip you make room.

Someday maybe i got the welding done i needed too for now:awesomework:

If the panel is totally full though how would i even go about it?

99redtj · Dec 5, 2010

there is ways to do it but can't tell you for sure intill i seen a picture of the panel and the type of breakers it already has in it.

some time take a picture of the breakers and i can tell you if it can be done.there are this breakers called peanut breakers that can be used.

boardbysled · Dec 5, 2010

War-Jeeper said:
Welded it up today, but found that my pinion bearing is toast (rather beyond it actually) So im out for this gotta pay for christmas gifts first so no money to fix the rig for a little while:booo:

I'll save my passenger seat if you want.:awesomework:

Maybe a good co-pilot can keep me from "pluggin":redneck:

Didn't get bad enough to destroy the ring/pinion did it?:eeek:

War-Jeeper · Dec 5, 2010

99redtj said:
there is ways to do it but can't tell you for sure intill i seen a picture of the panel and the type of breakers it already has in it.

some time take a picture of the breakers and i can tell you if it can be done.there are this breakers called peanut breakers that can be used.

will do! When i go by there tomorrow i will try and remember too

boardbysled said:
I'll save my passenger seat if you want.:awesomework:

Maybe a good co-pilot can keep me from "pluggin":redneck:

Didn't get bad enough to destroy the ring/pinion did it?:eeek:

You know that rattling noise in the front end at high speeds?

Well if you remember what im talkin about it was the pinion bearing the whole time

and im not sure about the ring and pinion yet i dont have the motivation to pull the cover and find out to be honest. I will also have to roll the axle up a bit to make it so this doesnt happen again probably have to cut the inner C's off and rotate them so it works properly:booo:

zuk88 · Dec 7, 2010

Should have my engine running good by then and join up with you all.

bobbed_84_toy · Dec 10, 2010

Are 2wd tow pigs allowed? :redneck:

tomsbrokeagain · Dec 10, 2010

bobbed_84_toy said:
Are 2wd tow pigs allowed? :redneck:

If you are talking your Ford..... good luck parking it and turning around.

bobbed_84_toy · Dec 10, 2010

tomsbrokeagain said:
If you are talking your Ford..... good luck parking it and turning around.

I could load the yota up on the deck of the Ford

tomsbrokeagain · Dec 10, 2010

bobbed_84_toy said:
I could load the yota up on the deck of the Ford

And you still might have to back down a ways.

Just try to get up there before the "granola munchers", get turned around before offloading and you will be fine.

I usually get up there REALLY EARLY to do just that. Yet I still get blocked in by a F***ing Subaru!

crash2 · Dec 10, 2010

tomsbrokeagain said:
And you still might have to back down a ways.

Just try to get up there before the "granola munchers", get turned around before offloading and you will be fine.

I usually get up there REALLY EARLY to do just that. Yet I still get blocked in by a F***ing Subaru!

I am going to block you in too :fawkdancesmiley: