Domestic(ated) (non)Violence 3-seater build

[chevota1]

nice build james cant wait to see it down at the hammers, jason said you found a tow down that true? you going to do much wheelin while your down or just pit stuff

 

[jimboy]

nice build james cant wait to see it down at the hammers, jason said you found a tow down that true? you going to do much wheelin while your down or just pit stuff

Wheel as much as possible of coarse! u?:beer::beer:

 

[chevota1]

was going to try and hang after the race for at least a day or two and wheel with some of the Canadians ill copilot for my boss day of the race as long as he gets in the big show

 

[gas is on the right]

:awesomework:sick welds dude ......

 

[TDW]

Plumbing for fuel, brakes, and steering is done.

The dash/guages are all wired up. He's reusing the motor from the last car where he had the intake turned around. On this car the intake was flipped back so the harness needs a little clipping and crimping to clean up the install. Should be firing it up this weekend.

Just a few random shots of what a mess final assembly can be.

 

[stealthrunner1]

Plumbing for fuel, brakes, and steering is done.

The dash/guages are all wired up. He's reusing the motor from the last car where he had the intake turned around. On this car the intake was flipped back so the harness needs a little clipping and crimping to clean up the install. Should be firing it up this weekend.

Just a few random shots of what a mess final assembly can be.

Nice work guys!!!!!:awesomework: and lets see a you tube vid when it gets fired up again!!!!I'll see ya's some time this summer!!!:corn::corn::beer:

 

[JoshC1]

are you running pulse arc on your welder?

 

[TDW]

are you running pulse arc on your welder?

No pulse arc, no trigger weld.

 

[TDW]

A few more random pics. The back of the dash, bench bleeding brake master, and installing the coilovers.

 

[TDW]

Nice work guys!!!!!:awesomework: and lets see a you tube vid when it gets fired up again!!!!I'll see ya's some time this summer!!!:corn::corn::beer:

Fired it up yesterday.

http://www.youtube.com/watch?v=n20s5QeBZtk

 

[dirtyhall]

Sick!

Very nice work!

 

[TDW]

A few small things to do but it's pretty much as done as it will be before KOH. Here's a few vids of pulling out of the garage.


http://www.youtube.com/watch?v=5rxV-TddgwQ

http://www.youtube.com/watch?v=a7rXkuU0pqo

http://www.youtube.com/watch?v=wPr5GNjT_xw

 

[TDW]

 

[TDW]

 

[TDW]

 

[stealthrunner1]

:awesomework: Bad ass as always Boys!!!!!:awesomework: What muffler and size of tube did you guys use for the exhaust????:eeek: :beer::beer:

 

[jimboy]

2.5 in. tubing. 4in round magnaflow muffler.

 

[stealthrunner1]

2.5 in. tubing. 4in round magnaflow muffler.

Thanks James!!!! like the sound of it going to use the same on my junk!!!!:awesomework::beer:

 

[jzmudbogger]

This rig is beautiful

 

[jimboy]

Thanks James!!!! like the sound of it going to use the same on my junk!!!!:awesomework::beer:

The magnflow mufflers create much less heat than a hushpower muffer and are not much louder.