Sold/Expired LQ4/9 with 4L80E with harness/ecu to run both

blacksheep10 · Oct 11, 2009

Just like cubby, need an LQ4/4L80E combo with harness and brain to control both. bought my shiny new Tcase with 32 in and will run 400 until I find this combo.

Have a complete running solid 5.3 with everyfuckingthing you could imagine down to fuel lines/intake system, etc etc. 2 sets of new accessories and 2 harnesses. I just want to dump it and some of my 400's and 350's and get fully with the gen III program.
whatchu got

Cubby · Oct 11, 2009

I've been beating the bushes pretty hard for one. I've got a line on a LY6, and a LQ9 @ the moment. Why not get a 6L80E if you're going with an electronic trans and then have the 4.0 1st gear.

cash talks · Oct 15, 2009

got one

PsDad · Oct 15, 2009

KELLY: Brokeass' bama boy might be interested in some of your gen I stuff. Need 2 sets of 5.7 rods and a buildable 1-piece rr main block. wachu got?

blacksheep10 · Oct 15, 2009

PsDad said:
KELLY: Brokeass' bama boy might be interested in some of your gen I stuff. Need 2 sets of 5.7 rods and a buildable 1-piece rr main block. wachu got?

what rods? I have a block that was zero decked and I didn't know it, put my balanced 4340 rotating assembly with 10:1 wiseco's in it and it interfered, so I ran a thick head gasket. It needs a new block that hasn't had so much deck taken off. Lower end is all still complete and turns by hand.
eagle H beam 6" rods bushed. forged wisecos, 4340 crank ground .020 I think. CHEAP right now. Have the Sportsman heads with new manley street flows, 64cc, angle plug, 220cc I think.
A couple 1 piece block here and there laying around,
Rods, ****, what you need. I have several several several 350's sitting here with one ailment or another, how many you want. I need to clean house.
wish you wanted big block stuff. I have 3 454's, a 366 rotating assembly for the steel crank to make a 427, on 454 block is std bore 4 bolt main, still pristine, AL intake, sets of heads, couple cranks, lots of rods.
Just tell me what you need, I BET I have it. laughing1

CheapJ7 · Oct 15, 2009

****.. what you want for a buildable or in good shape 454??

dads got that 51 chebby project it would be sweet in...

blacksheep10 · Oct 19, 2009

CheapJ7 said:
****.. what you want for a buildable or in good shape 454??

dads got that 51 chebby project it would be sweet in...

I have 3 454's, enough to make at least 1 complete one with great parts. 2.5 sets of heads (3.5 if you count the tall deck heads), perfect 4 bolt main std bore block with low miles, 366 rotating assembly (put this in a 454 block, makes a 427 and is a steel crank), a cam for a street rod, al intake for one, dist, 2 other 454's with wristpin breakage and ****ed blocks, still good cranks and 7 rods each, a full complete 427 tall deck truck engine std std. REally enough stuff to make a runner with little more than a head job and gasket kit. 427 is another story, it still runs, just weak. From our grain truck.
whatchu need.

1TONZR2 · Oct 19, 2009

not sure how much you are wanting to spend.....seems like his prices are pretty good. Justin is a good guy to deal with.
http://pirate4x4.com/forum/showthread.php?t=816884&highlight=efi+engine+supply

blacksheep10 · Oct 19, 2009

1TONZR2 said:
not sure how much you are wanting to spend.....seems like his prices are pretty good. Justin is a good guy to deal with.
http://pirate4x4.com/forum/showthread.php?t=816884&highlight=efi+engine+supply

Thanks for the heads up but my prices are a fudge lower than that guy's, and in KC.

1TONZR2 · Oct 19, 2009

thats cool....good luck finding one!

blacksheep10 · Oct 19, 2009

1TONZR2 said:
thats cool....good luck finding one!

I think cubby on here has me one found for the DIRTY CHEEP, just in ATL laughing1

Cubby · Oct 19, 2009

blacksheep10 said:
I think cubby on here has me one found for the DIRTY CHEEP, just in ATL laughing1

Hell, I can't get that guy on the phone for nothing. I think I sent you his info. See if you can get in touch with him some time. I'll make the ride to Atlanta to pick them up any night after work. I'm not too good at waiting...

blacksheep10 · Oct 20, 2009

i can wait....for money to appear. Have the coin to buy one or 2, just don't know whether to let go of it or buy other parts needed for mockup and build. It will run with my 5.3 in it. otoh, if you get ahold of him and it really is in the range we talked about, I'll take on, no questions asked.

Bones · Oct 20, 2009

I wanna see some bent tube! :****:

Cubby · Oct 20, 2009

blacksheep10 said:
i can wait....for money to appear. Have the coin to buy one or 2, just don't know whether to let go of it or buy other parts needed for mockup and build. It will run with my 5.3 in it. otoh, if you get ahold of him and it really is in the range we talked about, I'll take on, no questions asked.

If I can't find one I'll end up 5.3 as well. The 5.3 in Bigelow's buggy seems to be badass.
We'll see what happens.

BamaTJ · Oct 20, 2009

5.3, LS6 cam, headers, tune = good to go. I have heard you can get a lot of power out of those motors and they are the cheapest Gen III's out there...

1TONZR2 · Oct 20, 2009

thats exactly what I have, I love it. I changed my fuel pump to the e8248 pump that Woodlee suggested in a thread on pirate and it really woke it up....

sorry for the hi jack! :flipgotcha: