84turbotoy
Well-Known Member
Full bump pics 17" belly on 36's
-
Help Support Hardline Crawlers :
Some assembly required (A Toyota cab truck rebirth)
- Thread starter 84turbotoy
- Start date
84turbotoy
Well-Known Member
Well I guess I can call the cage done!!! 
I have to put a cross brace under the hood for the front shocks but that is nothing, also threw a seven dollar paint job on most of it. Hope I can get my rod ends this weekend and planning on going to get some 39.5 Irocks on beadlocks saturday!!!
I have to put a cross brace under the hood for the front shocks but that is nothing, also threw a seven dollar paint job on most of it. Hope I can get my rod ends this weekend and planning on going to get some 39.5 Irocks on beadlocks saturday!!!
Lil ugly
Well-Known Member
You should have something in the center of your roof. I am guessing that you are trying to retain the use of the sunroof, but having something come thru the roof in a roll over will suck big time.
84turbotoy
Well-Known Member
In reality this started as a tube bed and ended up an exo, I don't plan on rolling which no one ever does that being said this is more of a crawling beer drinking rig than all out acting stupid rolling setup.
Sent with telegraph
Sent with telegraph
race_jeep
Well-Known Member
I agree with this guy, with the rear 4 link and bigger tires you will be trying harder stuff, the rollover is inevitable.Lil ugly said:
TBItoy
Well-Known Member
Re: Re: Some assembly required (A Toyota cab truck rebirth)
With the shocks leaned that much I bet it will have crazy body roll, especially with tri uppers and straight lowers.
With the shocks leaned that much I bet it will have crazy body roll, especially with tri uppers and straight lowers.
CheapJ7
Mustache rides?
Re: Re: Some assembly required (A Toyota cab truck rebirth)
Sway bar time :afro:
TBItoy said:
Sway bar time :afro:
84turbotoy
Well-Known Member
Another thing is I am out of tube ant the money is going to tires and rod ends for the rear so the roof bars are destined for a later date. But I am sure the design will be improved in as I go. 
84turbotoy
Well-Known Member
New tires 
My rear axle rolled back on me pulled the drive shaft in two , the wheel base won't be that long.
My rear axle rolled back on me pulled the drive shaft in two , the wheel base won't be that long.
Lil ugly
Well-Known Member
The rear axle look about right where it is. 
and beer= Hey watch this!!!.
and beer= Hey watch this!!!.
race_jeep
Well-Known Member
Who the hell are you??????watkins said:Heck with any more roof bars, better make some YETI protection! Opening side looks exposed!
Nice build, but i am partial to blue Toyotas!
Keep it going. :afro:
Wade
84turbotoy
Well-Known Member
Finally getting some more done, I made it to Birmingham today and got the last bit of steel I need.
Started on my tabs and lower link mounts for the frame.
Boxed all the way out
Tabs for the rear axle
I only had two bolts so I will have to get some more tomorrow before I can start on the other bars :afro: but anyway it won't be long now!!!!
Started on my tabs and lower link mounts for the frame.
Boxed all the way out
Tabs for the rear axle
I only had two bolts so I will have to get some more tomorrow before I can start on the other bars :afro: but anyway it won't be long now!!!!
Lil ugly
Well-Known Member
Very nice job on the tabs. What are you using to cut and grind them to shape?
race_jeep
Well-Known Member
Just Werkin my ass off, holler at us n go ride sometime.watkins said:
What up cuz?
84turbotoy
Well-Known Member
Making huge progress last day or so! I needed some more tabs for the front of the uppers so I made some more tabs.
Then I cut a plate for the frame and to weld the tabs too for some strength. I welded the plate to the frame and then figured y separation and welded my tabs in place.
Tacked on my upper link mounts axle side then set my pinion angle just a fuzz and then measured and cut my links and yes they were the same length first try!
After all that I figured I would test flex it and this bitch will get loose!
got a lot more travel but the engine hoist wanted to flip lol!
I lowerd it just a bit from this pick but I have about 24 1/4" belly at this point, except the lower link mounts and they are 20'
Had to go do some **** pipe plumbing at my sisters
uke: and fooled aroud a bit making these before I cam in for the night.
Hope I got it finished by the weekend!
Then I cut a plate for the frame and to weld the tabs too for some strength. I welded the plate to the frame and then figured y separation and welded my tabs in place.
Tacked on my upper link mounts axle side then set my pinion angle just a fuzz and then measured and cut my links and yes they were the same length first try!
After all that I figured I would test flex it and this bitch will get loose!
got a lot more travel but the engine hoist wanted to flip lol!
I lowerd it just a bit from this pick but I have about 24 1/4" belly at this point, except the lower link mounts and they are 20'
Had to go do some **** pipe plumbing at my sisters
uke: and fooled aroud a bit making these before I cam in for the night.
Hope I got it finished by the weekend!
85buggy
Is there room to pass ?
Dude to b honest I saw this truck at RBD and thought
What the hell. Totally different looking ride at this point.
Great job IMO. Bet you can't wait to test it ????????????
What the hell. Totally different looking ride at this point.
Great job IMO. Bet you can't wait to test it ????????????
84turbotoy
Well-Known Member
85buggy said:
Yeah it was a whole lot of booty fab and an eye sore but I wan on the trail having a blast! Now its time to play with the big boys!
TBItoy
Well-Known Member
Re: Re: Re: Some assembly required (A Toyota cab truck rebirth)
One of the best "transformations" I've seen from a single owner!
Most of the time it's "once a booty fab hack jobber, always a booty fab hack jobber".
85buggy said:
One of the best "transformations" I've seen from a single owner!
Most of the time it's "once a booty fab hack jobber, always a booty fab hack jobber".
