-
Help Support Hardline Crawlers :
Renovation of a YJ
- Thread starter jimpaget
- Start date
zukkev
Cornfuzzled yet again...
Few pics of little progress! :haha:
some bracing between the tow points on rear bumper & frame...
Few pics of the front bumpstop mounts....didn't take into acct the position on the frame where the mounts were goin' on, but a small chunk of 1/2" round stock did the trick! (whew!:haha
...should be just the ticket for the angle...
The rear gear pattern looks ok...and un-benounced to me when I pulled the cover to check it out and get the new/used cover on (thanks Bunk!!!), it's got a spool, not a welded carrier!!! :cheer
Jim later informed me the PO said it was a spool!:redneck:...that or I didn't remember him telling me! :haha...
some bracing between the tow points on rear bumper & frame...
Few pics of the front bumpstop mounts....didn't take into acct the position on the frame where the mounts were goin' on, but a small chunk of 1/2" round stock did the trick! (whew!:haha
...should be just the ticket for the angle... The rear gear pattern looks ok...and un-benounced to me when I pulled the cover to check it out and get the new/used cover on (thanks Bunk!!!), it's got a spool, not a welded carrier!!! :cheer
Jim later informed me the PO said it was a spool!:redneck:...that or I didn't remember him telling me! :haha...Attachments
zukkev
Cornfuzzled yet again...
I guess the spool explains the high spline count on the axles....
Sweetness. Looking good!
the 30 spl axles are stockers for mid/late 70's era....but you knew that, right?:fawkdancesmiley: Thanks Andy! :haha:
zukkev
Cornfuzzled yet again...
Few pics of the finished bumpstops...didn't get any yet of them in action...gonna have to make a little pocket for the fronts as I missed the sweet spot by about 1/2" or so (too deep! :redneck...simple fix, and will also take care of another small concern with the shock mounts at the axle end up front :awesomework: ......the rears are tits on tho! :;
...simple fix, and will also take care of another small concern with the shock mounts at the axle end up front :awesomework: ......the rears are tits on tho! :;Attachments
boardbysled
Tree Nerd.
Does it really have that much uptravel?:eeek:
Looks good:awesomework:
Looks good:awesomework:
Yep.
Actually I am not sure that the weight was completely on the wheels, but there is a lot of flex.
Last edited:
zukkev
Cornfuzzled yet again...
:awesomework:
Pics look like it's got alot more than it does...~ 4.5" uptravel in front and rear....bumpstops set at 4" to contact pads all the way around...
Pics look like it's got alot more than it does...~ 4.5" uptravel in front and rear....bumpstops set at 4" to contact pads all the way around...
zukkev
Cornfuzzled yet again...
boardbysled
Tree Nerd.
Next, take the body lift out?
Wanna do the pathy next?:fawkdancesmiley::haha:
Wanna do the pathy next?:fawkdancesmiley::haha:
zukkev
Cornfuzzled yet again...
Been workin' on getting the winch mounted---tried to make one of those universal winch plates look....well....not so universal!! :haha: Turned out pretty good I think. Just need to get the winch wired, and the rope on it. Thanks again to Master Pull for the :bling: !!!
Don't know why the 2nd pic wigged out :eeek:...they were cell pics as my camera was up at the house.
Don't know why the 2nd pic wigged out :eeek:...they were cell pics as my camera was up at the house.
Attachments
zukkev
Cornfuzzled yet again...
I don't know why, but I just now saw this!!! :haha: :haha: :haha:
:ANYWORD: :redneck:
boardbysled
Tree Nerd.
Only needs new front springs. Again.
how did you pull that off????
zukkev
Cornfuzzled yet again...
Again??????? Whatthe...Only needs new front springs. Again.
Welcome to Kev's used 4x4 parts emporium!:redneck:
:haha::haha: that is so true!:haha::haha:
Zoediak
Well-Known Member
Been workin' on getting the winch mounted---tried to make one of those universal winch plates look....well....not so universal!! :haha: Turned out pretty good I think. Just need to get the winch wired, and the rope on it. Thanks again to Master Pull for the :bling: !!!
Don't know why the 2nd pic wigged out :eeek:...they were cell pics as my camera was up at the house.
in your third pic....
you are going to open that hole up a bit more behind the 'bling' right?? from the picture it is looking a bit restrictive....
I'm. Looking at it now and what you are seeing is the plate on the back leading edge of the winch plate......:awesomework:
